Microwave Peanut Brittle - Bake. Eat. Repeat. (2024)

FAQs

Why is my microwave peanut brittle too hard? ›

Why is my peanut brittle too hard? Peanut brittle can end up too hard when the temperature gets too high during the cooking process. With a microwave peanut brittle recipe like this one, you may need to adjust the cooking times based on your microwave.

The main reason why peanut brittle doesn't get hard and have the crunch we expect is because the sugar was not cooked long enough. The sugar needs to be cooked to what is called the hard crack stage, 300ºF.

So, I Googled Salvaging Undercooked Peanut Brittle and followed Tiffany's helpful instructions to throw the pieces back in the pan, turn the heat up and stir, stir, and stir to a raging boil and wait to pour it in the pan until it reaches 300 degrees.

Baking soda releases bubbles into our candy (you can see this on a more extreme level in my honeycomb recipe, which uses 5x the amount of baking soda!). This makes the brittle more delicate, crisp, and less chewy, which ultimately makes it more snappy and less likely to obnoxiously stick to your teeth.

Why is it too hard? Using baking soda usually prevents peanut brittle from being too, well, brittle. However, if you cook the candy past the set temperature or overwork the candy once you spread it out onto the cookie sheet, that can cause it to become very hard and difficult to bite through.

The mixture will foam and grow so make sure to stir constantly to completely incorporate. Working quickly, pour into prepared 10×15 pan. To keep the brittle light and airy, do not spread or flatten the mixture. Instead, let it flow freely.

If your peanut brittle is too soft, you didn't cook it long enough.

I've learned that brittle is better when made on a cool, dry day. When I've made the candy on a warmer, humid day, it tends to be a stickier brittle. This is because the brittle takes longer to cool, and it reaches a point where it is no longer evaporating moisture into the air.

Carefully pour the hot mixture onto the prepared pan and use a knife or spoon to quickly (and carefully!) spread the mixture into an even layer. Allow to cool completely (at least 30 minute) before breaking apart and eating. Store the completely cooled peanut brittle in an airtight container.

You'll also want to prepare a baking sheet, with either a silicone mat or parchment paper. The mat/paper will help ensure the peanut brittle doesn't stick directly to pan once it has cooled.

Can peanut brittle go bad? ›

How Long Does Peanut Brittle Last? Properly stored (in an airtight container at room temperature), peanut brittle will last one to two months.

When candy cools slowly on a stone slab, more crystals have a chance to form. With a higher number of micro-crystals, the sugar has more sites on which to crystallize, and so crystallization ultimately happens faster.

Peanut brittle has one redeeming quality: peanuts. Outside of that single ingredient, peanut brittle is painfully unhealthy. It contains: sugar, corn syrup, and butter, all of which are unhealthy for your body in different ways.

Many recipes call for buttering a foil-lined baking sheet, which can result in a tasty but greasy brittle. That is, unless you missed a spot while buttering. In which case you have peanut-and-foil brittle.

Pralines have a lot in common with nut brittle, with the difference being mostly in the addition of cream and the cooking temperature––the sugary syrup used to coat pralines is heated to a soft-ball consistency, a lower temperature than the hard-crack stage of peanut brittle.

Microwave oven roasting: Pour peanuts into colander or wire basket and wet thoroughly. Sprinkle with salt. Pour into small microwave safe casserole or pie plate. Microwave for 2 1/2 minutes; stir, microwave 2 1/2 minutes longer.

Thoroughly rinse the raw unshelled peanuts in water. Put the water, salt, seasoning, peanuts in a large stockpot, bring to a boil: Cover and reduce the heat just enough to maintain a low boil. Boil for 2 to 3 hours or longer (some boil their peanuts all day), until peanuts reach desired level of softness.

Place the peanut butter in the microwave, and heat it for 30 seconds. Once the 30 seconds is up, stir the peanut butter to makes sure it's melting evenly. Place the peanut butter back in the microwave for another 30 seconds, and stir again. This will probably take a few rounds to get to your desired consistency.

After softening in the microwave, I would recommend mixing in some oil that isn't too flavorful. I found mixing in a bit of water works fine though. You could even make your own mixes to make that last little portion of nut butter count by mixing in honey, unrefined coconut oil, or even Nutella if you so desire!